cisco_inter_vlan_routing
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| cisco_inter_vlan_routing [2024/01/21 00:23] – [Logical Interfaces] walkeradmin | cisco_inter_vlan_routing [2024/01/21 13:36] (current) – walkeradmin | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Cisco Inter VLAN Routing ====== | ====== Cisco Inter VLAN Routing ====== | ||
| + | ==== aka Switch Virtual Interfaces (SVI) or Management Interface ==== | ||
| <color # | <color # | ||
| \\ | \\ | ||
| Line 149: | Line 150: | ||
| Now that we have two devices connected to our VLAN and each VLAN has an IP Address in each Subnet, we can Ping our two devices from the Switch Interface: | Now that we have two devices connected to our VLAN and each VLAN has an IP Address in each Subnet, we can Ping our two devices from the Switch Interface: | ||
| \\ | \\ | ||
| + | \\ | ||
| + | <color # | ||
| < | < | ||
| ping 192.168.1.38 | ping 192.168.1.38 | ||
| Line 192: | Line 195: | ||
| \\ | \\ | ||
| \\ | \\ | ||
| - | To enable IP Routing on the switch, we will use the following: | + | To enable |
| \\ | \\ | ||
| + | en | ||
| + | conf t | ||
| + | ip routing | ||
| + | end | ||
| + | There is no text return from running this command. | ||
| \\ | \\ | ||
| + | \\ | ||
| + | No we can test to see the routes by using the following: | ||
| < | < | ||
| sh ip route | sh ip route | ||
| + | |||
| Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP | Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP | ||
| D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area | D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area | ||
| Line 211: | Line 222: | ||
| C 192.168.1.0/ | C 192.168.1.0/ | ||
| </ | </ | ||
| + | \\ | ||
| + | We can see that the two <color # | ||
| \\ | \\ | ||
| \\ | \\ | ||
| - | <color #ed1c24>**** seems my switch doesn' | + | Now try to ping from Device A (192.168.1.38) to Device B (10.43.30.100). Remember, the gateway of Device A must be the IP Address of VLAN 10 (192.168.1.1 in this example). |
| + | \\ | ||
| + | <file> | ||
| + | Pinging 10.43.30.100 with 32 bytes of data: | ||
| + | Reply from 10.43.30.100: bytes=32 time<1ms TTL=127 | ||
| + | Reply from 10.43.30.100: bytes=32 time=1ms TTL=127 | ||
| + | Reply from 10.43.30.100: | ||
| + | Reply from 10.43.30.100: | ||
| + | </file> | ||
| + | Now we can communicate with devices in VLAN 20 from VLAN 10. | ||
| \\ | \\ | ||
| \\ | \\ | ||
cisco_inter_vlan_routing.1705796583.txt.gz · Last modified: by walkeradmin